Experimental Physics and Industrial Control System
The record definition and dbpr output looks OK to me.
In your original post you said:
> The driver works, however if the update rate is lower than 1 second,
> strange warning appears in the console at the time of every refresh
When you say "lower than 1 second" do you mean the time between callbacks in your driver is less than 1 second, i.e. the usleep() value is less than 1000000?
> (and that's only for one of 4 channels), namely:
> 2017/04/11 15:42:08.682 PIEZO:OSC-CH0-WAVEFORM
> devAsynFloat64Array::interruptCallbackInput
> \000\000\000\000\000@\205?\000\000\000\000\000\300\202?\000\000\000\000\000\000\204?\000\000\000\000\000\000\204?\000\000\000\000\000\300\202?\000\000\000\000\000\000\204?\000\000\000\000\000@\205?\000\000\000\000\000\000\204?\000\000\000\000\000\300\202?\000\000\000\000\000\000\204?
Is the output coming because you have enabled some asynTrace?
> 2017/04/11 15:42:08.682 PIEZO:OSC-CH0-WAVEFORM
> devAsynFloat64Array::processCommon, warning, multiple interrupt callbacks between processing
Are you saying that this warning message only happens on the first waveform record, not on all of them? That message is printed with this code in devAsynXXXArray.h:
if (pPvt->gotValue) { \
asynPrint(pPvt->pasynUser, ASYN_TRACE_WARNING, \
"%s %s::processCommon, " \
"warning: multiple interrupt callbacks between processing\n", \
pr->name, driverName); \
} \
Note that it is printed with the ASYN_TRACE_WARNING mask. How have you called asynSetTraceMask in your startup script? Is it possible you set it like this?
asynSetTraceMask(testAPD, 0, 255)
If so that would explain why you are only seeing the messages for the first waveform record. The asynTrace is specific to the asyn address, and this only enables asynTrace on address 0. To see the messages from all 4 waveform records you can do this:
asynSetTraceMask(testAPD, -1, 255)
or this
asynSetTraceMask(testAPD, 0, 255)
asynSetTraceMask(testAPD, 1, 255)
asynSetTraceMask(testAPD, 2, 255)
asynSetTraceMask(testAPD, 3, 255)
This would not explain why you are getting the messages in the first place, but it would explain why you are only seeing them for the first waveform record.
Mark
-----Original Message-----
From: Paweł Plewiński [mailto:[email protected]]
Sent: Tuesday, April 11, 2017 1:55 PM
To: Mark Rivers
Cc: [email protected]
Subject: Re: [AsynPortDriver] "Multiple interrupt callbacks between processing" warning with multiple arrays
Hi Mark,
thanks for quick answer. Actually I forgot to post the record, but it
had SCAN set to I/O INTR, similarly to the example project. Here's the
record definition:
record(waveform, "PIEZO:OSC-CH$(CHANNEL)-WAVEFORM")
{
field(DTYP, "asynFloat64ArrayIn")
field(INP, "@asyn($(PORT),$(ADDR),$(TIMEOUT))OSC_WAVEFORM")
field(FTVL, "DOUBLE")
field(NELM, "$(NPOINTS)")
field(LOPR, "0")
field(HOPR, "10")
field(SCAN, "I/O Intr")
}
As for the commands you asked for, the results are, respectively:
ACKS: NO_ALARM ACKT: YES APST: Always ASG:
ASP: (nil) BKPT: 00 BPTR: 0xbcb3e0 BUSY: 0
DESC: DISA: 0 DISP: 0 DISS:
NO_ALARM
DISV: 1 DPVT: 0xc05690 DSET: 0x7f2dbdcea9a0
DTYP: asynFloat64ArrayIn EGU: EVNT: 0
FLNK:CONSTANT 0 FTVL: DOUBLE HASH: 0 HOPR: 10
INP:INST_IO @asyn(testAPD,0,1)OSC_WAVEFORM LCNT: 0
LOPR: 0 LSET: 0xc07f40
MLIS: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
MLOK: b0 b3 bc 00 00 00 00 00 MPST: Always
NAME: PIEZO:OSC-CH0-WAVEFORM NELM: 1000 NORD: 1000
NSEV: NO_ALARM NSTA: NO_ALARM PACT: 0 PHAS: 0
PINI: NO PPN: (nil) PPNR: (nil) PREC: 0
PRIO: LOW PROC: 0 PUTF: 0 RARM: 0
RDES: 0xb86470 RPRO: 0 RSET: 0x7f2dbda73340
SCAN: I/O Intr SDIS:CONSTANT SEVR: NO_ALARM
SIML:CONSTANT
SIMM: NO SIMS: NO_ALARM SIOL:CONSTANT SPVT:
0xc135e0
STAT: NO_ALARM TIME: 2017-04-11 20:53:12.153366126 TPRO: 0
TSE: 0 TSEL:CONSTANT UDF: 0 VAL: (nil)
ACKS: NO_ALARM ACKT: YES APST: Always ASG:
ASP: (nil) BKPT: 00 BPTR: 0xbcd3a0 BUSY: 0
DESC: DISA: 0 DISP: 0 DISS:
NO_ALARM
DISV: 1 DPVT: 0xc05be0 DSET: 0x7f2dbdcea9a0
DTYP: asynFloat64ArrayIn EGU: EVNT: 0
FLNK:CONSTANT 0 FTVL: DOUBLE HASH: 0 HOPR: 10
INP:INST_IO @asyn(testAPD,1,1)OSC_WAVEFORM LCNT: 0
LOPR: 0 LSET: 0xc07f60
MLIS: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
MLOK: 70 d3 bc 00 00 00 00 00 MPST: Always
NAME: PIEZO:OSC-CH1-WAVEFORM NELM: 1000 NORD: 1000
NSEV: NO_ALARM NSTA: NO_ALARM PACT: 0 PHAS: 0
PINI: NO PPN: (nil) PPNR: (nil) PREC: 0
PRIO: LOW PROC: 0 PUTF: 0 RARM: 0
RDES: 0xb86470 RPRO: 0 RSET: 0x7f2dbda73340
SCAN: I/O Intr SDIS:CONSTANT SEVR: NO_ALARM
SIML:CONSTANT
SIMM: NO SIMS: NO_ALARM SIOL:CONSTANT SPVT:
0xc138f0
STAT: NO_ALARM TIME: 2017-04-11 20:53:29.910249080 TPRO: 0
TSE: 0 TSEL:CONSTANT UDF: 0 VAL: (nil)
ACKS: NO_ALARM ACKT: YES APST: Always ASG:
ASP: (nil) BKPT: 00 BPTR: 0xbcf360 BUSY: 0
DESC: DISA: 0 DISP: 0 DISS:
NO_ALARM
DISV: 1 DPVT: 0xc060e0 DSET: 0x7f2dbdcea9a0
DTYP: asynFloat64ArrayIn EGU: EVNT: 0
FLNK:CONSTANT 0 FTVL: DOUBLE HASH: 0 HOPR: 10
INP:INST_IO @asyn(testAPD,2,1)OSC_WAVEFORM LCNT: 0
LOPR: 0 LSET: 0xc07f80
MLIS: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
MLOK: 30 f3 bc 00 00 00 00 00 MPST: Always
NAME: PIEZO:OSC-CH2-WAVEFORM NELM: 1000 NORD: 1000
NSEV: NO_ALARM NSTA: NO_ALARM PACT: 0 PHAS: 0
PINI: NO PPN: (nil) PPNR: (nil) PREC: 0
PRIO: LOW PROC: 0 PUTF: 0 RARM: 0
RDES: 0xb86470 RPRO: 0 RSET: 0x7f2dbda73340
SCAN: I/O Intr SDIS:CONSTANT SEVR: NO_ALARM
SIML:CONSTANT
SIMM: NO SIMS: NO_ALARM SIOL:CONSTANT SPVT:
0xc13c00
STAT: NO_ALARM TIME: 2017-04-11 20:54:17.907769453 TPRO: 0
TSE: 0 TSEL:CONSTANT UDF: 0 VAL: (nil)
ACKS: NO_ALARM ACKT: YES APST: Always ASG:
ASP: (nil) BKPT: 00 BPTR: 0xa7b540 BUSY: 0
DESC: DISA: 0 DISP: 0 DISS:
NO_ALARM
DISV: 1 DPVT: 0xab0810 DSET: 0x7efec944b9a0
DTYP: asynFloat64ArrayIn EGU: EVNT: 0
FLNK:CONSTANT 0 FTVL: DOUBLE HASH: 0 HOPR: 10
INP:INST_IO @asyn(testAPD,3,1)OSC_WAVEFORM LCNT: 0
LOPR: 0 LSET: 0xab21d0
MLIS: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
MLOK: 10 b5 a7 00 00 00 00 00 MPST: Always
NAME: PIEZO:OSC-CH3-WAVEFORM NELM: 1000 NORD: 1000
NSEV: NO_ALARM NSTA: NO_ALARM PACT: 0 PHAS: 0
PINI: NO PPN: (nil) PPNR: (nil) PREC: 0
PRIO: LOW PROC: 0 PUTF: 0 RARM: 0
RDES: 0xa30650 RPRO: 0 RSET: 0x7efec91d4340
SCAN: I/O Intr SDIS:CONSTANT SEVR: NO_ALARM
SIML:CONSTANT
SIMM: NO SIMS: NO_ALARM SIOL:CONSTANT SPVT:
0xabe140
STAT: NO_ALARM TIME: 2017-04-11 20:52:33.970326348 TPRO: 0
TSE: 0 TSEL:CONSTANT UDF: 0 VAL: (nil)
Best regards,
Paweł
W dniu 2017-04-11 18:24, Mark Rivers napisał(a):
> Hi Pawel,
>
> What is the SCAN field of your waveform record? I suspect it is
> probably periodic ("1 second", etc.). For this application you should
> set it to SCAN="I/O Intr". Then the waveform record will process each
> time your driver does a callback to device support. If the record is
> periodically processing at 1 second and your driver is doing callbacks
> faster than 1 Hz then you will see the error you report.
>
> Mark
>
>
> -----Original Message-----
> From: [email protected]
> [mailto:[email protected]] On Behalf Of Pawel Plewinski
> Sent: Tuesday, April 11, 2017 8:49 AM
> To: [email protected]
> Subject: [AsynPortDriver] "Multiple interrupt callbacks between
> processing" warning with multiple arrays
>
> Hi,
>
> I've recently written asyn-based device support for a custom device
> communicating over PCIe. One of its functions is to periodically
> retrieve 4 waveforms from 4 channels, which is done in a separate
> thread, from which the callback function is called to notify asyn about
> change. I heavily based the code on the AsynPortDriver example.
> The driver works, however if the update rate is lower than 1 second,
> strange warning appears in the console at the time of every refresh
> (and
> that's only for one of 4 channels), namely:
>
> 2017/04/11 15:42:08.682 PIEZO:OSC-CH0-WAVEFORM
> devAsynFloat64Array::interruptCallbackInput
> \000\000\000\000\000@\205?\000\000\000\000\000\300\202?\000\000\000\000\000\000\204?\000\000\000\000\000\000\204?\000\000\000\000\000\300\202?\000\000\000\000\000\000\204?\000\000\000\000\000@\205?\000\000\000\000\000\000\204?\000\000\000\000\000\300\202?\000\000\000\000\000\000\204?
> 2017/04/11 15:42:08.682 PIEZO:OSC-CH0-WAVEFORM
> devAsynFloat64Array::processCommon, warning, multiple interrupt
> callbacks between processing
>
> The parameters passed to the top level constructor are
> : asynPortDriver(portName,
> 4, /* maxAddr */
> (int)NUM_SCOPE_PARAMS,
> asynInt32Mask | asynFloat64Mask |
> asynFloat64ArrayMask | asynEnumMask | asynDrvUserMask, /* Interface
> mask
> */
> asynInt32Mask | asynFloat64Mask |
> asynFloat64ArrayMask | asynEnumMask, /* Interrupt mask */
> ASYN_MULTIDEVICE, /* asynFlags. This driver does
> not block and it is not multi-device, so flag is 0 */
> 1, /* Autoconnect */
> 0, /* Default priority */
> 0) /* Default stack size*/
>
> The readback thread code:
>
> void piezoPortDriver::readbackTask(void)
> {
> while (1) {
> bool stopped = false;
>
> lock();
> auto new_data = osc->fetch_data(vtim, vdat);
> unlock();
>
> if (!stopped)
> {
> lock();
> this->osc_update_trigger();
> unlock();
> }
> callParamCallbacks();
>
> for (int i = 0; i < 4; i++){
> doCallbacksFloat64Array(vdat[i].data(), vdat[i].size(),
> P_OscWaveform, i);
> }
> usleep(100000);
> }
> }
>
> The fetch_data method reads four 1000-element double vectors from PCIe.
>
> Could you give me some suggestions what may be wrong?
>
> Regards,
> Paweł Plewiński
> Department of Microelectronics and Computer Science
> Lodz University of Technology
- Replies:
- Re: [AsynPortDriver] "Multiple interrupt callbacks between processing" warning with multiple arrays Paweł Plewiński
- References:
- [AsynPortDriver] "Multiple interrupt callbacks between processing" warning with multiple arrays Paweł Plewiński
- RE: [AsynPortDriver] "Multiple interrupt callbacks between processing" warning with multiple arrays Mark Rivers
- Re: [AsynPortDriver] "Multiple interrupt callbacks between processing" warning with multiple arrays Paweł Plewiński
- Navigate by Date:
- Prev:
Re: sumitomo f70 compressor Lionberger, Carl A.
- Next:
Re: [AsynPortDriver] "Multiple interrupt callbacks between processing" warning with multiple arrays Paweł Plewiński
- Index:
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
<2017>
2018
2019
2020
2021
2022
2023
2024
- Navigate by Thread:
- Prev:
Re: [AsynPortDriver] "Multiple interrupt callbacks between processing" warning with multiple arrays Paweł Plewiński
- Next:
Re: [AsynPortDriver] "Multiple interrupt callbacks between processing" warning with multiple arrays Paweł Plewiński
- Index:
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
<2017>
2018
2019
2020
2021
2022
2023
2024