Experimental Physics and
Industrial Control System

[email protected] · Tue, 27 Jul 2004 23:16:27 +0900

Hello Kate,

Mr OH was added on what you attached Makefile.inc and mvme5500.cfg files.
Tried again to make utility after cleared before error messages, but the other error messages are
¡°compiled for a little endian system and target is big endian¡±.

Error Messqges:
File in wrong format: failed to merge target specific data of file /opt/rtems/lib/gcc-lib/pp
c-rtems/3.2.1/../../../../ppc-rtems/lib/libbfd.a(archive.o)
/opt/rtems/lib/gcc-lib/ppc-rtems/3.2.1/../../../../ppc-rtems/bin/ld: /opt/rtems/lib/gcc-lib/
ppc-rtems/3.2.1/../../../../ppc-rtems/lib/libbfd.a(archures.o): compiled for a little endian
 system and target is big endian

File in wrong format: failed to merge target specific data of file /opt/rtems/lib/gcc-lib/pp
c-rtems/3.2.1/../../../../ppc-rtems/lib/libbfd.a(archures.o)
/opt/rtems/lib/gcc-lib/ppc-rtems/3.2.1/../../../../ppc-rtems/bin/ld: /opt/rtems/lib/gcc-lib/
ppc-rtems/3.2.1/../../../../ppc-rtems/lib/libbfd.a(bfd.o): compiled for a little endian syst
em and target is big endian

File in wrong format: failed to merge target specific data of file /opt/rtems/lib/gcc-lib/pp
c-rtems/3.2.1/../../../../ppc-rtems/lib/libbfd.a(opncls.o)
/opt/rtems/lib/gcc-lib/ppc-rtems/3.2.1/../../../../ppc-rtems/bin/ld: /opt/rtems/lib/gcc-lib/
ppc-rtems/3.2.1/../../../../ppc-rtems/lib/libbfd.a(reloc.o): compiled for a little endian sy
stem and target is big endian

He used patch files version are below:
binutils-2.13.2.1
gcc-3.2.1
rtems-ss-20030128

Did you used different of patch versions for MVME5500 target?

Sorry for much a question.

Kind regards,
Kiman.
PLS Control and taskforce team.

> 
> 
> -----Original message-----
> From: "KateFeng" 
> To: [email protected]
> Cc: [email protected],[email protected]
> Date: 07/27/2004(Tue)02:33
> Subject: Re: RTEMSfor MVME5500
> 
> [email protected] wrote:
> 
> > Hello Kate,
> >
> > >RTEMS-4.6.0 is better than  RTEMS-4.6.0pre#.   RTEMS-4.6.0 has
> > >PowerPC patches  for RTEMS-4.6.0pre#.
> > He tried to recompile RTEMS-4.6.0 kernels and GeSys_2.1beta codes.
> > All passed before step what for build cexp : and xsyms :
> >
> > >To build rtems5500-cexp.bin and rtems5500-cexp.sym :
> > >0) cd RTEMS5500-GeSys_2.1.beta
> > >1) make
> >
> > Did you used bspcheck commands at Makefile line 142.
> 
> Till Straumann wrote the  original Makefile, which I  added the
> support for the mvme5500.   It appears to me bspcheck
> is not a command.  Searching  the Makefile,  I got
> two lines regarding  bspcheck.
> 
> bspcheck: $(if $(filter $(RTEMS_BSP_FAMILY),pc386 mvme5500 motorola_powerpc
> svgm),,bspfail)
> 
> and
> 
> all: bspcheck libnms ${ARCH} $(SRCS) $(PGMS)
> 
> 
> >
> > But when i type make commands after other error messages from Makefile line 142..
> > What is missing ?
> >
> > root@rtemsdev RTEMS5500-GeSys_2.1.beta]# make
> > Makefile:142: *** GeSys has not been ported/tested on this BSP (mvme5500) yet.
> >
> > Makefile: 142 Line :
> > all: bspcheck libnms ${ARCH} $(SRCS) $(PGMS)
> >
> 
> I could not duplicate your error message.   What message did you
> get before those error message came out ?
> 
> Make sure you have  environment variable :
> RTEMS_MAKEFILE_PATH=/opt/rtems/ppc-rtems/mvme5500
> 
> However, I do find out that you are missing
> /opt/rtems/make/custom/mvme5500.cfg (attached).
> 
> Also,  one has to modify the  RTEMS5500-GeSys_2.1.beta/config
> files  (e.g. libbfd.excl, libiberty.excl, and  libopcodes.excl)
> to change the path from /opt/rtems3 to its own defined directory.
> The same as  the ppc-rtems/mvme5500/Makefile.inc file.
> 
> Regards,
> Kate
> 
> 
> 
> 
> 
> 
> 

Experimental Physics and Industrial Control System

Experimental Physics and
Industrial Control System