Hi Kristi,
Yes, it would be helpful to know what you mean. Do you think that the card is failing to respond to the commands, or that the commands are not propagating down to the card? Is it an intermittent problem? Could you enable the asyn trace before the call to config2?
I have had problems with 'new' OMS cards being configured with non-default settings, so I always have RDF as my first command in the configuration string.
Regards,
Austen Rose
(x8495)
-----Original Message-----
From: Mark Rivers [mailto:[email protected]]
Sent: 07 March 2014 12:18
To: Luchini, Kristi L.; [email protected]
Subject: RE: MAXv model-3 driver - omsMAXvConfig problem
Can you be more specific about what you mean by "the axis configuration settings don't always seem to stick for every axis"?
Do you mean they are not restored correctly after a reboot? Or do they get lost while the IOC is running?
Mark
________________________________________
From: [email protected] [[email protected]] on behalf of Luchini, Kristi L. [[email protected]]
Sent: Thursday, March 06, 2014 6:48 PM
To: [email protected]
Subject: MAXv model-3 driver - omsMAXvConfig problem
Hello,
We have seen a problem with the MAXv omsAsyn support, where the axis configuration settings don't always seem to Stick for every axis. We have a temporary workaround, where to use the MAXv command "APP" which saves the configuration settings as the Power-up default.
Has anyone implemented a solution to this problem?
Details:
EPICS R4.13.12
RTEMS-R4.9.4
MVME6100
MAXv-8000 FW 1.44
- Regard,
Kristi
--
This e-mail and any attachments may contain confidential, copyright and or privileged material, and are for the use of the intended addressee only. If you are not the intended addressee or an authorised recipient of the addressee please notify us of receipt by returning the e-mail and do not use, copy, retain, distribute or disclose the information in or attached to the e-mail.
Any opinions expressed within this e-mail are those of the individual and not necessarily of Diamond Light Source Ltd.
Diamond Light Source Ltd. cannot guarantee that this e-mail or any attachments are free from viruses and we cannot accept liability for any damage which you may sustain as a result of software viruses which may be transmitted in or with the message.
Diamond Light Source Limited (company no. 4375679). Registered in England and Wales with its registered office at Diamond House, Harwell Science and Innovation Campus, Didcot, Oxfordshire, OX11 0DE, United Kingdom
- References:
- MAXv model-3 driver - omsMAXvConfig problem Luchini, Kristi L.
- RE: MAXv model-3 driver - omsMAXvConfig problem Mark Rivers
- Navigate by Date:
- Prev:
Re: Sequencer is not monitoring Pvs from another IOC Benjamin Franksen
- Next:
RE: MAXv model-3 driver - omsMAXvConfig problem Luchini, Kristi L.
- Index:
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
<2014>
2015
2016
2017
2018
2019
2020
2021
2022
2023
2024
- Navigate by Thread:
- Prev:
RE: MAXv model-3 driver - omsMAXvConfig problem Mark Rivers
- Next:
RE: MAXv model-3 driver - omsMAXvConfig problem Luchini, Kristi L.
- Index:
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
<2014>
2015
2016
2017
2018
2019
2020
2021
2022
2023
2024
|