Subject: |
[Fwd: align CPU Error message????] |
From: |
"Leonard J. Reder" <[email protected]> |
To: |
"EPICS Tech Talk (E-mail)" <[email protected]> |
Date: |
Wed, 29 Jan 2003 10:11:02 -0800 |
Hello,
Not sure what to make of this error message but since the message
below says to email tech-talk I thought I would see if others
have information for me on this. See below.
Len
-------- Original Message --------
Subject: align CPU Error message????
Date: Wed, 29 Jan 2003 10:08:50 -0800
From: "Leonard J. Reder" <[email protected]>
Hello Kevin,
Mark and Andrew asked me to add some instances of btSeq for k1.m11 and
k2.m11 on the ldls. I attempted this and noticed the error given below.
I put the old start up script back in place and got this error. It was
booting up fine before or maybe I just did not notice this error message
once in awhile. At any rate all the main sequencer tasks are running
but
for each sequencer there is no fault or commanding task running.
I am not sure what is going on here so for now I will just finish adding
the new keywords. Here is the error message:
k1m6pAlign: A call to "assert (semTake(client_lock, WAIT_FOREVER)==OK)"
failed in ../iocinf.c at 1046
Please send a copy of the output from "tt (0xfde078)" and a copy of this
message
to the author or "[email protected]"
This problem occurred in "@(#)Version R3.13.0.beta.12 $$Date: 1998/08/18
02:02:32 $$"
k1m7pAlign: A call to "assert (semTake(client_lock, WAIT_FOREVER)==OK)"
failed in ../access.c at 1074
Please send a copy of the output from "tt (0xfbb510)" and a copy of this
message
amoeba Flux, Pixels, Radius, Xcen, Ycen = 26.053 27106 998.846 428.953
-1112.784
errlog = 14 messages were discarded
filename="../taskwd.c" line number=175
task 10a2c68 seqAux suspended
Here is the output from tt,
al>tt 0xfde078
176cb4 vxTaskEntry +60 : sequencer (1096f10, 2710, 1094cd8)
17d1b44 sequencer +a4 : seq_connect (1096f10)
17cf9e8 seq_connect +17c: seq_pvMonitor (1096998, 28)
17d4544 seq_pvMonitor +164: ca_flush_io ()
174be38 ca_flush_io +98 : cac_mux_io (fddf38)
1743aa4 cac_mux_io +24 : cac_clean_iiu_list ()
17408cc cac_clean_iiu_list+74 : epicsAssert (176eb64, 416, 176eb70, 0)
1737a14 epicsAssert +14c: taskSuspend ()
value = 0 = 0x0
Also I think I will send this out to tech-talk and see if any
interesting replies come back.
Thanks,
Len
--
____________________________________________________
Leonard J. Reder
Jet Propulsion Laboratory
Interferometry Systems and Technology Section 383
Email: [email protected]
Phone (Voice): 818-354-3639
Phone (FAX): 818-354-4357
Mail Address:
Mail Stop: 171-113
4800 Oak Grove Dr.
Pasadena, CA. 91109
---------------------------------------------------
- Replies:
- RE: [Fwd: align CPU Error message????] Jeff Hill
- Navigate by Date:
- Prev:
Can't build the CMLOG under Tornado 2.0 for mv162, ppc etc. Vladis Korobov
- Next:
Re: [Fwd: align CPU Error message????] Allan Honey
- Index:
1994
1995
1996
1997
1998
1999
2000
2001
2002
<2003>
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
2021
2022
2023
2024
- Navigate by Thread:
- Prev:
Re: Can't build the CMLOG under Tornado 2.0 for mv162, ppc etc. Chip Watson
- Next:
RE: [Fwd: align CPU Error message????] Jeff Hill
- Index:
1994
1995
1996
1997
1998
1999
2000
2001
2002
<2003>
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
2021
2022
2023
2024
|