Note:   Programming to be done with No Power to Rack.   For Timer 1 the desired configuration is:

No Power to Rack                                                With Rack Active Rack Active

Goes to this configuration when Rack Active

A. To start programming mode

Press "prog" button and hold for 3-5 seconds.   At the end of that time display will show.

B. To set timer relay configuration

Press "Prog" button as many times as necessary to display.

  Press "Reset" button when you have the desired relay configuration.

C. To set time scale (hrs., mins., secs.)

Press "Prog" button as many times as necessary to display.

Prog

0

SEC

Press reset button when you have the desired time scale

D. To set delay time (least significant digit)

The desired setting is 180, least signficant digit can be set   by pressing "Prog" button until desired # is set, when set, press "Reset" button and display will move to next signficant digit

Depending on unit, least significant digit will flash or will be flashing

E. To set delay time (next significant digit)

Press "Prog" button until the desired # is set, when set press "Reset" button and the display will move to the next significant digit

Digit flashing

or

symbol flashing

F. To set delay time (most significant digit)

Press "Prog" button until the desired # is set

Press "Reset" button

Digit flashing

or

symbols flashing

G. Set trigger type [Level (LEU) or Edge (Edg)]

Press "Prog" button to display LEU

Press "Reset" button when desired trigger type is indicated

1. The timer now reviews your selected setting (if changes were made)

Timer 2 - The same sequence is now done for Timer 2.   The desired configuration is [Note - Trigger type is Edg], and desired configuration is the same Rack Active or not.

•  To start programming mode:

Press "Prog" button and hold for 3-5 seconds, at the end of that time display will show

B. To set timer relay configuration:

Press "Prog" button as many times as necessary to display

Press "Reset" button when you have the desired relay configuration.

C. To set time scale (hrs., mins., secs):

     Press "prog" button as many times necessary to display

Press reset button when you have the desired time scale.

D. To set delay time (least significant digit)

The desired setting is 003, least significant digit can be set by pressing "Prog" button until desired # is set, when set press "Reset" button and display will move to next significant digit

Depending on unit, least significant digit will flash or will be flashing

 

E. To set delay time (next significant digit)

Press "Prog" button until the desired # is set, when set press "Reset" button and the display will move to the next significant digit

Digit flashing

or

symbol flashing

F. To set delay time (most significant digit)

Press "Prog" button until the desired # is set

Press "Reset" button

Digit flashing

or

Symbols flashing

G. Set trigger type [Level (LEU) or Edge (Edg)]

Press "Prog" button to display Edg

Press "Reset" button when desired trigger type is indicated

H. The timer now reviews your selected setting (if changes were made)

If the selection is correct -Press "Reset" button	PROG ss	(Timer relay Conf.) If incorrect press "Prog" button until you have the correct selection then press "Reset"(time scale)
If selection is correct - Press "Reset" button	PROG 0 SEC	If incorrect press "Prog" button until you have the correct selection then press "Reset" [time setting (lsd)]
If selection is correct - Press "reset" button	PROG 003 SEC ss PROG 003 SEC ss	Flashing Or Flashing In incorrect press "Prog" button until you have the correct selection, then press "Reset" Flashing or Flashing
If selection is correct - Press "Reset" button		If incorrect press "Prog" button until you have correct selection - then press "Reset"

If the selection is correct -Press "Reset" button	PROG 003 SEC ss	Flashing or Flashing (Time Setting MSD) If incorrect, press "Prog" button until you have the correct selection, then press "Reset"
If selection is correct - Press "Reset" button	PROG   Edg	(Trigger type) If incorrect press "Prog" button until you have correct selection, then press "Reset"
	3 SEC ss       O       O	Operational state (Rack active or not)